Z Automotive Z-TZR-JLM Tazer JL Mini Programmer for 18+ Jeep Wrangler JL & Gladiator JT
Tazer JL Mini aims to be an essential tool for owners of the 2018+ Wrangler JL and Jeep Gladiator. All engine and transmission variations supported, including export models.
Simple, plug-in installation – simply unplug the SGW module and plug the Tazer JL Mini in its place. Located above the OBD2 Diagnostic connector. To make it easier for removal and reinstallation for dealer visits, add on our SGW Extension Cable.
Features are all accessed using the dash display, using steering wheel buttons to navigate the menus.
Tazer JL Mini features can be broken into three categories:
NEW in firmware 11.4.1 (11/14/22):
PIN Lock allows you to set a steering wheel button sequence (PIN) that must be entered before the vehicle can be driven. Learn more in your Tazer’s User Manual.
NOTE: Disable PIN Lock before going through a carwash or before handing the keys off to a valet.
Vehicle Settingsare accessed with theengine OFFand the ignition in the “RUN” position. These are changes made to the Jeep such as tire size, gear ratios or settings which accommodate other upgrades. These changes will continue to operate after the Tazer JL Mini is unplugged.
Live Functionsare accessed with theengine ON. These are operations the Tazer JL Mini performs live, only while it is physically connected. plugged in.
“Non-Menu” Live Functionsarenot located in a menu.They areactivated automatically or with a steering wheel button combination.These are operations the Tazer JL Mini performs live, only while it is physically connected.
List of Vehicle Settings:
Light Show – 6 preset and 3 make-your-own light shows that flash all the exterior lights – perfect for car shows/first responders/off-road visibility – controlled from key fob or steering wheel buttons – can be enabled in-motion for use in parades, off-road and for legal police/EMS applications (contact support for more info) read and clear DTCs system-wide or in specific modules
change tire size
change gear ratio (max 4.50 on 4XE)
change Transfer Case LOW ratio
enable/disable TPMS system
set TPMS pressure warning limit, front and rear, between 25psi and 85psi
enable/disable backup camera
enable/disable Cargo Camera input (8.4 UConnect only)
enable/disable CD (wired audio) input*
enable/disable TravelLink/XM traffic and weather
activate Offroad Pages after upgrading to 8.4” radio
change daytime running lights (DRL) region (CA/USA)
change DRL location
enable/disable DRL Dropout function
enable/disable factory fog lights
enable/disable Fog Light Dropout (when fogs shut off while high beams are on)
enable/disable one-touch lane change
enable/disable factory halo lights (including BCM output for adding halos)
change headlight type (Std/LED)
change fog light type (Std/LED)
change taillight type (Std/LED)/delete sensor circuit for running aftermarket lights
change front turn signal type (std/LED)/delete sensor circuit for aftermarket lights
enable/disable factory auto hi-beam
enable/disable Trailer Tow setting
disable electronic sway bar (if removed from the vehicle)
disable electronic steering pump for hydraulic steering conversions
enable the trailer brake controller (primarily Gladiator)
disable front and rear lockers for axle swaps
disable front axle disconnect module for axle swaps
declare the presence of a Drive Train Control Module (Rubicon Transfer Case)
enable/disable Aux Buttons
enable/disable Blind Spot Detection (if the hardware is added or removed)
When shipping denotes a $0 value, team will email you a freight quote, it does NOT mean freight is $0.
You will receive a freight estimate ASAP which you can choose to accept (complete the purchase), or deny, (abandon purchase).
Shipping will be calculated at checkout using the best available freight based on your location. Some large items and or oversized items can be purchased and the Double Black team will email you within 24 hours with a seperate freight invoice.